Frigidaire washer no water
Common reasons your Frigidaire washer has no water
The most common reasons your Frigidaire washer has no water are a defective dispenser, malfunctioning electronic control board or a clogged water valve assembly.
54% of the time it's the
Dispenser24% of the time it's the
Electronic Control Board12% of the time it's the
Water Valve Assembly10% of the time it's the
Something else
Schedule your washer repair now!
We can help! Our service technicians have repaired over 40,000 Frigidaire washers. We can fix yours no matter where you bought it.
Most common repairs needed to fix a Frigidaire washer
Dispenser Replacement
A defective washer dispenser can result in a failure to allow water into the wash tub and the incomplete release of detergent, fabric softener or bleach at the designated stage of the wash cycle. This issue often arises due to the integration of water valves into modern dispenser assemblies. Signs of a defective dispenser include detergent remaining in the dispenser compartment after a cycle, signaling incomplete dispensing. You may also notice no water or an insufficient amount of water in the tub. There is also the potential for water to leak into the wash tub from the dispenser.
Electronic Control Board Replacement
A malfunctioning electronic control board can lead to various failures in a washer. This is because the board serves as the brain of the washer, controlling crucial components such as the water valve, drive motor, drain pump, and cycles. If the electronic control board fails, the washer may not power up or display the cycle status. Additionally, it might fail to fill, agitate, spin, or drain. In some cases, a shorted board may emit a burning smell.
Water Valve Assembly Replacement
The water valve assembly controls water flow into the washer. A clogged water valve inlet screen will prevent the wash tub from filling with hot water, cold water or both. Electrical failures in the valve may also prevent the valve from opening to allow water into the tub. The valve connects your home’s water supply to the washer. A faulty valve may begin leaking into the tub or around the connections to the water supply hoses. If you suspect a faulty water valve assembly, have a Sears Home Services professional inspect the washer and replace the valve if needed.
Why is my Frigidaire washing machine not filling with water?
Watch this video and get DIY troubleshooting tips to discover if the problem is your washing machine water valves, a kink in the water hose or some type of clog.
1. Check that the lid is completely closed.
Washing machines have a safety switch that prevents the washer from operating if the lid is open. If you’re washer isn’t filling with water, make sure the lid is completely closed.
If it is closed, check to see if the strike on the lid is broken, preventing it from making contact with the lid switch. If the strike is broken, it should be replaced.
2. Make sure the hot and cold water supplies are on.
It may seem obvious, but it’s possible the water supply faucet handles aren’t on. Ensure both the hot and cold water faucets are in the “on” position. You may want to move them to “off” and then to “on” again.
3. See if the fill hoses are kinked.
Check the hoses that lead from water supply to the back of the machine and make sure they’re not kinked. If you do find a kink, reposition the hose to remove the kink, and make sure the hoses remain in a position that prevents kinking again.
4. Check if the water inlet screens are clogged.
Sometimes the screens on the water inlet valve become clogged with mineral buildup. Remove the water fill hoses from the inlet valve and use a soft cloth to clean the screens. Don’t remove the screens — this could possibly cause flooding. If the screens are clogged and you can’t get them clean, the water valve should be replaced.
After checking the screens, reinstall the hoses and turn the water back on. Make sure there aren’t any leaks.
Advanced Troubleshooting and Repair Tips
If your washing machine fails to fill with water after basic troubleshooting, there might be underlying issues that warrant repair. One possible culprit could be a faulty water inlet valve. Over time, these valves can become clogged with debris, preventing the free flow of water. A malfunctioning valve requires replacement.
A faulty pressure switch could also cause the washer not fill. The pressure switch monitors the water level in the machine and sends signals to start or stop the filling process. A malfunctioning pressure switch might incorrectly signal that the desired water level has been reached, causing the machine to not fill properly.
Another potential source of the issue could be a malfunctioning control board or timer. If these components fail to communicate the appropriate signals, the washing cycle may not fill or may start to fill but with not enough water to perform a wash cycle.
A blockage or obstruction within the machine's internal hoses or filters could restrict water flow. Sediment buildup or foreign objects might impede the passage of water, necessitating a thorough cleaning or replacement of affected components. In such cases, seeking professional repair services can help diagnose and rectify the underlying problems, ensuring your washing machine resumes its normal functionality.
Here's an advanced DIY troubleshooting video that shows how to systematically check all issues that can prevent a common top-load washer from filling.
Check Water Flow
Check for water flow through the fill hoses by unplugging the washer, turning off the faucets and disconnecting the hoses from the back of the washer. Hold each hose end over a bucket and briefly turn on the faucet. If you don't have any water coming out, check for a clog in the hoses. If the hoses are okay, you could have a problem with your house water supply.
Is water inlet valve working?
Check for continuity through the entire electrical circuit with a multimeter. This will tell us if the cold-water valve is getting the current it needs to open. For safety, always unplug your washer before checking continuity. Shut off the water supply. Pull the plastic end caps off the sides of the control console. Remove the screws at the base of the control console. Pull the control console slightly forward and then swing it up and over the top of the back panel. Unplug the wire harness from the lid switch on the washer's top panel. Release the clips that secure the cabinet to the washer's back panel. Using a slot screwdriver, pry the clips forward to release them. Lift the back of the cabinet and slide it forward to remove it from the washer frame.
Set your multimeter to check resistance. Place one meter probe on the right prong of the power cord and the other on the yellow and red wire connected to the cold water valve. You should see near 0 ohms of resistance, which indicates that you have a clear path for voltage to the cold water valve in the rinse portion of the cycle. Next, check the other side of the circuit. Put your leads on the white wire and the left prong of the outlet cord. You should have continuity through the neutral side of the circuit as well. If you had continuity on both sides of the circuit, then the cold water valve is apparently getting voltage but not opening to allow water flow, meaning you’ll need to replace your water inlet valve.
Check for Broken Wires
If you didn’t have continuity on either wire—on this meter that’s a “1” in the far left corner—then do more checks to find the break in the circuit. If the white wire didn’t have continuity, you’ll need to check each section of wiring until you find the break and repair any broken wires that you find. This video has more information about repairing wires.
Check the Pressure Switch
If the water inlet valve isn’t the problem, the next thing to check is the water level pressure switch. If the yellow/red wire didn't have continuity, check from the power cord to the pressure switch. Place one meter lead on the right prong of the power cord and the other on the pink wire on the water level pressure switch. If you measure no continuity, check between the violet and pink wires on the pressure switch. If you measure no continuity there, then the break must be in the pressure switch. This video will show you how to replace your pressure switch: How to Replace the Water Level Pressure Switch in a Top-Load Washer.
Test for a Bad Timer or Wiring Failure
Now, if you measured continuity between the violet and pink wires, the problem is either the timer or a wiring failure in the circuit. Check for continuity on the violet wire between the timer and the water level pressure switch. If there's no continuity on the violet wire then that wire will need to be repaired. If there is continuity on the violet wire, check between the violet wire and the black wire on the timer. If you measure no continuity, you’ll need to replace the timer because it's not allowing voltage through the circuit. This video will show you how: How to replace the timer in a top-load washer.
If you’ve got continuity through the timer, then you must have a break in wiring harness between the timer and the power cord. Find and repair that break.
Let the Washing Machine Experts at Sears Home Services Repair Your Washer
If you've gotten this far in the troubleshooting and haven't found and fixed the cause of the filling problem, it's likely time to have a professional fix your washing machine.
Sears Home Services stands ready to provide trusted expertise to address even the most complex washing machine issues. With a team of skilled technicians experienced in diagnosing and repairing a wide range of appliance problems, we’ll have your washer working again fast. Schedule a service appointment with a washer repair expert today.
What to expect when you experience a Frigidaire washer no water issue
How is the no water problem fixed?
Correcting most no water problems usually involves replacing the dispenser, electronic control board or water valve assembly. However, there are many potential causes, so a thorough diagnosis is key to fixing the problem. An accurate diagnosis is essential to understanding how much the repair will be.
Sears Home Services recommendations for a washer that has no water
When the washer has no water it can be for many reasons. To avoid replacing unneeded parts we recommend having a Sears Home Services professional perform diagnostic tests to identify the root cause of the problem. Our technicians are experienced at diagnosing all types of washer failures.
What to look out for with a washer no water diagnosis
Diagnosing modern appliances without proper knowledge and training can be difficult. Without using proper diagnostic techniques, fixing your washer problem will only be achieved through changing parts on a hunch. Appliances, especially in the last 10 years, have become extremely advanced, and many models have electronic parts that are difficult to test. DIY repairs on the latest appliance models are becoming increasingly difficult.
A Frigidaire washer that never fills leaves clothes spinning in air. Stuck inlet valves or broken sensors commonly block water flow. Instead of half-clean laundry, ask for washing machine service. Sufficient water ensures each cycle thoroughly rinses out dirt.
What our customers say about us
With more than 1.3 Million 5 Star Reviews, you don't have to take our word for it
Thanks
Thanks for your expert analysis of the problem that caused the flooding of my home .I was scared the first few times I used the machine , but all is working great.
Frank U, Coconut Creek, FL
Excellent service.
Pleasant person to work with. He explains things to you.
Jacklyn J, Bessemer, AL
Very Professional
Very professional, thoughtful and knowledgeable I would highly recommend him.
Marilyn W, Covington, LA
Repair Washer Resources
If your washing machine making loud noises, we’ll help you discover the causes and simple solutions.
Explore the top reasons why your washing machine might be leaving clothes excessively wet, from issues with cycle selection to potential drainage problems.
Dealing with a washing machine that won't stop filling with water can be a frustrating experience.
Discover how to unclog your washer's drain hose with our step-by-step guide. Say goodbye to frustrating clogs with our expert tips!
Glossary Terms
Hard water is water that contains high levels of dissolved minerals, particularly calcium and magnesium. It contrasts with soft water, which has lower concentrations of these minerals.
A washing machine pedestal is a platform that raises the washer off the ground, providing easier access to the appliances and often includes additional storage space such as drawers.
A washer tub is the interior part of a washing machine where clothes are placed for washing, typically made of stainless steel, plastic, or porcelain-coated metal, designed to hold water and withstand the agitation or spinning during the wash cycle.
Fabric softener is a laundry additive used to soften and freshen clothing, reduce static cling, and make fabrics feel smoother.